Bambu Lab P1S user guide

Bambu Studio setup

Install

  1. Install and launch Bambu Suddio
  2. Click "Get Started"
    Bambu Studio welcome page
  3. Select "Europe"
    Bambu Studio region selection page
  4. Select "Skip"
    Bambu Studio data hoover page
  5. Select "Clear All"
    Bambu Studio printer selection page with default options
  6. Check "Bambu Lab P1S 0.4mm nozzle" and click "Next"
    Bambu Studio printer selection page with correct printer selected
  7. Customise the filament selection if needed, otherwise just click "Next"
    Bambu Studio filament selection page
  8. Ensure "Install Bambu Network plug-in" is checked and click "Finish"
    Bambu Studio network plugin install page

Add printer

  1. Switch to the "Devices" tab
    Bambu Studio devices tab with no printer added
  2. Click on "No printer" and select "3DP-01P-744" from the list
  3. When prompted enter the code for the appropriate printer listed here (or via the printer menu as instructed if that code did not work, make sure to update the wiki if you had to do this). Bambu Studio printer access code screen
  4. The printer status should now be shown in the "Device" tab
    Bambu Studio devices tab printer added

If you do not see the printer in the device list then most likely your machine is not properly configured to act as an SSDP client. See Simple Service Discovery Protocol and Printer Network Ports for more info. TL;DR: open UDP port 2021 on your machines firewall and try again.

Loading, Unloading and Configuring Filament

Unloading

  1. Ensure the filament you wish to remove from the AMS is not currently loaded into the printer
  2. Pull the filament out of the AMS feeder and lift the spool out

You can tell if a filament is loaded into the printer either by:

  • Observing the tube connecting the AMS to the printer, if you cannot see the filament in question inside the tube then it is probably unloaded
  • Checking the diagram on the "Device" tab in Bambu Studio, if the line leading from the spool position is thin and grey then the filament is unloaded

Loading

Bambu Lab filament

  1. Place the spool in a free AMS slot
  2. Push the filament into the AMS feeder for the corresponding slot
  3. Wait 30 seconds or so for the filament to be identified
  4. Verify that the filament was correctly identified via the "Devices" tab in Bambu Studio

Generic filament on Bambu Lab spools

  1. Place the spool in a free AMS slot
  2. Push the filament into the AMS feeder for the corresponding slot
  3. In the "Device" tab of Bambu Studio, click the edit icon on the just loaded AMS slot (may show either an "?" or the settings for the last non RFID filament used in that slow)
    Bambu Studio AMS status showing unknown filament inserted
  4. Edit the parameters and click "Confirm"
    Bambu Studio filament settings dialog
  5. The "Devices" tab should now show the filament type you specified
    Bambu Studio AMS status showing configured filament

External filament caddy (Kirisame only)

TODO

Printing

Preparing printer

  1. Ensure there are no obstacles above or below the bed and that the build plate is correctly seated, located by the white tabs on the rear corners (highlighted in red squares in the photo below)
    Front of printer prior to a print
  2. If you need to change filaments in the AMS, do so now

Preparing and starting job

  1. Load designs into the "Prepare" tab of Bambu Studio
    Bambu Studio prepare tab
  2. Synchronise local filament settings with AMS by clicking the Bambu Studio AMS sync button button on the filament settings panel, this will ensure your local filament settings reflect what is currently available on the printer
  3. Set machine, material and slicing settings in the left hand pane (yes the slicing profiles say "X1C", as far as I can tell this is fine)
  4. Click "Slice plate"
  5. You will see a preview in the "Preview" tab
    Bambu Studio preview tab
  6. If all is well, press "Print plate"
  7. Set options as desired, if you forgot to set the filament for your part you can override this here, disable timelapse if you have no intention of retrieving it, keep bed levelling and AMS enabled
    Bambu Studio job options
  8. Click "Send"
  9. Wait for the job to be uploaded
    Bambu Studio job uploading
  10. The "Device" page is automatically shown where you can monitor the jobs progress, adjust settings and temperatures if needed and pause or cancel the job
  11. It is worth checking that the purge filament has not ended up on the build plate, this should not happen but it is worth keeping an eye out for

End of job

  1. Remove build plate from printer
  2. Remove part from build plate
  3. Reseat build plate in printer
  4. Clean up any filament the printer has deposited (check the purge chute at the rear of the machine)

SD card

The micro SD card is used for storing print jobs, timelapse and camera recordings (amongst other things that are of little direct use to humans).

Do not use the SD card as a means of getting print jobs onto the machine.

Removing the SD card is how you would get timelapses and camera recordings off the printer, however if you wish to do this then immediately return the card to the printer as removal of the card renders it inoperative.

Should the card be out of space, it can be safely formatted in the printer using the on screen menu.